Classic Fixer · Knoxville, Tennessee

Detailed Rental Property Turnover Checklist

A professional turnover is a complete walk-through, documented scope, properly sequenced repair plan, and final rent-ready verification. Check every room the same way, photograph conditions, separate required repairs from owner options, and never claim a visual check is a licensed inspection or safety certification.

Prepare the work order before the walk-through

Start with the lease-end report, tenant notes, owner standards, known maintenance history, access instructions, utilities status, and authorization limit. Use a consistent room-by-room checklist so small items do not disappear between vendors.

  • Confirm vacancy, keys, lockbox, alarm, pet, parking, and utility status
  • Record property address, unit, manager, owner requirements, and desired rent-ready date
  • Confirm the not-to-exceed limit and which items require separate estimates
  • Note tenant-responsibility items separately according to the manager's policies
  • Take an opening set of wide-angle photos before moving or removing anything

Exterior, approach, and building entry

The turn starts at the curb. Document maintenance and safety concerns that affect first impressions, water control, access, and security.

  • Address numbers visible; mailbox and exterior lights intact
  • Walkways, steps, porches, decks, and handrails secure with no obvious trip hazards
  • Siding, fascia, soffit, trim, screens, and exterior caulk checked for visible damage
  • Roof and gutters observed from the ground for obvious damage; downspouts direct water away
  • Yard, drainage, trash, abandoned belongings, and vegetation documented
  • Exterior hose bibs checked for dripping, damage, or freeze concerns
  • Entry door, frame, weatherstripping, threshold, deadbolt, knob, peephole, and doorbell checked
  • All provided keys, remotes, fobs, garage controls, and mailbox keys accounted for

Whole-home safety and required devices

Document the presence, location, physical condition, manufacturer date label when visible, and response to the built-in test button for smoke and carbon-monoxide alarms. Device placement, replacement intervals, and requirements vary by product and applicable rules; questionable, missing, damaged, or out-of-date units should be reported for proper replacement.

  • Smoke alarms present in the required or owner-specified locations
  • Carbon-monoxide alarms present where required or specified, especially when fuel-burning equipment or an attached garage is present
  • Built-in TEST button operated only when safe; chirping, failure, damage, missing covers, and painted-over units documented
  • Manufacture or replace-by dates photographed when visible; batteries replaced or devices replaced only as authorized
  • Fire extinguisher, if the property provides one: confirm presence, mounting, visible physical condition, gauge position when equipped, and date or service tag
  • Classic Fixer does not inspect, service, recharge, or certify fire extinguishers; any concern is documented for a qualified fire-protection provider
  • Emergency egress paths, bedroom windows, stairs, railings, and obvious trip hazards documented
  • Any gas odor, burning smell, sparking, active leak, or other immediate hazard is escalated rather than treated as a routine punch-list item

Walls, ceilings, drywall, and the paint decision

Do not automatically call for a full repaint—or assume touch-ups will disappear. Evaluate cleanliness, damage, sheen, color consistency, prior patching, sunlight, and owner standards room by room.

  • Photograph holes, anchors, nail pops, dents, peeling, stains, cracks, crayon, grease, and heavy scuffs
  • Identify whether ceiling or wall staining may indicate an unresolved leak before closing or painting
  • Repair drywall and match texture before primer and finish paint
  • Touch up isolated marks only when matching paint and sheen are available and the blend will be acceptable
  • Paint selected walls when damage or color mismatch is limited to defined wall planes
  • Paint the full room when several walls are worn, patched, stained, or unlikely to blend
  • Consider whole-house painting when colors are inconsistent, wear is widespread, smoke or odor treatment is required, or the owner wants a uniform leasing standard
  • Inspect ceilings, doors, casing, baseboards, closets, shelving, and trim separately; record exact rooms and surfaces to avoid vague paint scopes
  • Confirm paint color, sheen, number of coats, repair allowances, and whether closets, ceilings, trim, and doors are included

Windows, blinds, doors, and hardware

Operate accessible components gently and document anything that does not open, close, latch, lock, or stay in position.

  • Windows open, close, lock, and remain supported; cracked glass, failed screens, moisture, and damaged sills noted
  • Blinds present where required, clean, correctly sized, mounted securely, and operating without broken slats or cords
  • Curtain rods, brackets, and abandoned wall anchors removed or repaired according to owner standards
  • Interior and closet doors open, close, latch, and clear flooring
  • Door stops, hinges, knobs, privacy locks, bifold tracks, and closet hardware checked
  • Exterior locks rekeyed or changed according to management policy; spare keys verified
  • Cabinet and closet shelving secure; loose or sharp hardware corrected

Floors, trim, and transitions

Walk the edges as well as the middle of every room. Flooring problems often show first near doors, appliances, toilets, tubs, and exterior entries.

  • Carpet checked for stains, tears, odors, loose transitions, and cleaning or replacement needs
  • LVP, laminate, tile, and wood checked for broken, loose, swollen, separated, or heavily scratched areas
  • Soft or discolored flooring near plumbing documented and investigated before covering
  • Baseboards, quarter round, thresholds, stair nosing, and transition strips secure and complete
  • Loose fasteners, exposed tack strip, sharp edges, and trip hazards corrected
  • Flooring work completed after wet trades and most painting, then protected during final work

Kitchen: cabinets, plumbing, and appliances

Check the kitchen systematically from the ceiling down, then operate accessible appliances and fixtures only when utilities are safely connected.

  • Cabinet doors, drawers, hinges, pulls, shelving, toe kicks, and drawer stops checked
  • Countertops, backsplash, sink rim, and wall joints checked for damage and failed caulk
  • Faucet hot and cold operation, sprayer, aerator, leaks, and secure mounting checked
  • Sink drains, traps, supply lines, angle stops, disposal, dishwasher connections, and cabinet floor observed for leaks or damage
  • Range or cooktop checked for cleanliness, physical damage, stable anti-tip protection where applicable, knobs, elements or burners, and oven racks
  • Electric range drip bowls or burner pans checked for missing, burned-through, mismatched, heavily soiled, or damaged pieces and replaced with a matching set when authorized
  • Range hood or microwave light, fan, grease filter, mounting, and visible condition checked
  • Appliance bulbs checked where safely accessible—including oven, range hood, microwave, and refrigerator lights—and replaced with the correct appliance-rated bulb when authorized
  • Refrigerator clean, level, cooling, sealed, and free of abandoned food; shelves, drawers, handles, ice/water connections, and interior light checked
  • Dishwasher racks, door seal, mounting, drain connection, and a short operating check completed when appropriate
  • GFCI receptacles tested using their built-in controls when safe; loose, damaged, hot, or nonworking devices referred for appropriate electrical service

Bathrooms

Bathrooms require both a function check and a water-damage check. Run fixtures long enough to reveal active leaks while monitoring the surrounding floor and accessible connections.

  • Toilet secure at the floor; seat, lid, handle, fill, flush, shutoff, supply line, and base checked
  • Tub and shower valve, trim, spout, showerhead, stopper, drain speed, and hot/cold operation checked
  • Tub, shower, vanity, backsplash, and fixture caulk inspected for gaps, staining, and failure
  • Vanity doors, drawers, top, faucet, pop-up, trap, supplies, shutoffs, and cabinet floor checked
  • Exhaust fan operated and cover cleaned; obvious noise, poor draw, or damage documented
  • Mirror, lights, GFCI, towel bars, toilet-paper holder, shower rod, and door hardware secure
  • Flooring and subfloor indicators checked around the toilet, tub, shower, and vanity
  • Mildew-like staining, persistent moisture, or suspected contamination documented; remediation needs are not concealed with caulk or paint

Bedrooms, living areas, halls, and closets

Use the same repeatable sequence in every room: ceiling, walls, openings, electrical, fixtures, floor, trim, and closet.

  • Ceiling fan and light controls operated; wobble, noise, missing globes, and dead or mismatched bulbs noted
  • Interior, closet, vanity, ceiling-fan, and other provided light bulbs checked and replaced with the correct type, base, shape, color temperature, and wattage limit when authorized
  • Switches, cover plates, and accessible receptacles visually checked for damage or looseness
  • HVAC supply and return grilles present, secure, and reasonably clean
  • Closet rods, shelves, doors, tracks, and lights checked
  • Window coverings and screens checked room by room
  • Bedrooms checked for appropriate egress and safety-device coverage according to management standards
  • Abandoned cables, mounts, hooks, nails, adhesive, and wall anchors handled according to the approved scope

Laundry, mechanical areas, and utilities

Record equipment condition and data plates when useful, but keep the turnover walk-through within safe visual and operating checks.

  • Washer valves, hoses, box, drain, and surrounding wall and floor checked for leaks or damage
  • Dryer cord or gas connection, transition duct, rigid duct path, exterior termination, flap, and lint accumulation observed
  • HVAC filter size and condition recorded; filter replaced when authorized
  • Thermostat operated through an appropriate basic check without forcing extreme settings
  • Water heater area checked for visible leaks, corrosion, damaged pan, discharge-pipe concerns, and stored combustibles
  • Electrical panel remains unobstructed; missing covers, open knockouts, heat, buzzing, or damage referred to a licensed electrician
  • Fuel-burning equipment, gas piping, venting, and combustion safety are not certified through a general turnover walk-through

Final plumbing and electrical pass

After repairs, make one uninterrupted pass through the property so no fixture, light, or temporary shutoff is forgotten.

  • Run faucets and check accessible cabinets and traps for leaks
  • Flush every toilet and confirm it stops filling
  • Confirm tubs, showers, and sinks drain normally
  • Check hose bibs and visible shutoffs without forcing seized valves
  • Operate lights, fans, and provided appliance controls
  • Confirm interior, exterior, closet, vanity, ceiling-fan, and appliance bulbs operate; use the correct bulb type and never exceed the fixture or appliance wattage rating
  • Confirm cover plates, globes, bulbs, and fixtures are present and secure; nonworking lights that remain after a correct bulb replacement are documented for fixture, socket, wiring, or appliance diagnosis
  • Document anything requiring a licensed plumber, electrician, HVAC contractor, roofer, remediation company, pest provider, or other specialist

Cleaning, odor, pests, and final presentation

Repairs are not rent-ready until dust, debris, labels, and leftover materials are removed and the property presents consistently.

  • Cabinets, drawers, closets, appliances, fixtures, floors, windowsills, and trim cleaned
  • Range drip bowls, hood filter, refrigerator, oven, dishwasher, and disposal area receive final attention
  • Construction dust, paint residue, stickers, abandoned belongings, and trash removed
  • Odors documented and source addressed rather than covered with fragrance
  • Visible pest evidence documented for the appropriate provider
  • Touch-up paint and owner-approved spare materials labeled and stored as directed
  • Exterior entry, porch, and immediate approach receive a final appearance check

Rent-ready closeout and owner documentation

The final report should let a manager or owner understand the property without driving across town. It should also clearly distinguish completed work, observations, deferred items, and specialist recommendations.

  • Final wide-angle photos of every room plus close-ups of completed repairs
  • Before-and-after photos organized by work-order item
  • Completed scope, labor notes, and materials documented clearly
  • Smoke and CO alarm observations and test-button results recorded without claiming certification
  • Fire extinguisher presence, visible date or tag, and condition documented only when one is provided
  • Keys, remotes, windows, locks, appliances, thermostats, and utilities left in the instructed condition
  • Open recommendations, owner-deferred work, warranties, and follow-up vendors listed
  • Manager receives one clear rent-ready status: complete, complete with documented exceptions, or awaiting specified follow-up

Quick checklist

  • Confirm access, utilities, deadline, and approval limit
  • Photograph every room before work
  • Check smoke and carbon-monoxide alarms and visible date labels without claiming certification
  • Document any provided fire extinguisher and visible date or service tag—refer certification to a qualified provider
  • Inspect locks, windows, screens, blinds, doors, stops, and hardware
  • Choose touch-ups, selected-wall painting, room painting, or whole-house painting based on actual condition
  • Inspect drywall, ceilings, trim, flooring, thresholds, and transitions
  • Check kitchen cabinets, plumbing, appliances, range hood, stove drip bowls, and appliance bulbs
  • Check every bathroom fixture, drain, shutoff, fan, accessory, caulk joint, and surrounding floor
  • Check bedrooms, living areas, halls, closets, interior and exterior light bulbs, fans, and HVAC grilles
  • Check laundry connections, dryer vent, HVAC filter, water-heater area, and utility access
  • Complete final plumbing, electrical, cleaning, key, and appliance pass
  • Send organized before-and-after photos, labor/material notes, exceptions, and recommendations